# What pressure should an industrial compressed air system run at?

**What working pressure should an industrial compressed air system run at?**

Under the Compressed Air Challenge Fact Sheet #4 (May 2026), equipment should be specified and operated at the lowest efficient operating pressure; Fact Sheet #1 says that level is set by the end uses and must take into account losses in dryers, separators, filters and piping.

## Start from the end uses

Fact Sheet #1 (May 2026) says different tools and process operations require different pressures: pneumatic tool manufacturers rate tools for specific pressures, and process engineers should specify the pressure requirements of process operations. Required pressure levels must take into account system losses from dryers, separators, filters and piping.

According to Fact Sheet #3 (May 2026), most systems have one or more critical applications that determine the minimum acceptable pressure, and in some cases dedicated storage or a reduced differential on those applications allows the overall system pressure to come down.

## Figures given by the fact sheets

- Fact Sheet #4: many plant air compressors operate with a full load discharge pressure of 100 psig and an unload discharge pressure of 110 psig or higher, while many types of machinery and tools can operate efficiently with an air supply at the point of use of 80 psig or lower.
- Fact Sheet #4: a typical pressure differential for a filter, pressure regulator and hose is 7 psid, but it could be much higher in poorly designed and maintained systems.
- Fact Sheet #6 (May 2026): the control range between the upper and lower pressure levels of the compressor control can be anywhere from 2 to 20 psi, depending on air system demand.

## What extra pressure costs

- Fact Sheet #1: a rule of thumb is that every 2 psi increase in operating pressure requires an additional 1% in operating energy costs.
- ULTRASEC datasheet (Ultra Controlo): the estimated power consumption for an increase of 1 bar on the compressor is about 7% of the installed motor power.
- Fact Sheet #4: elevating system pressure increases unregulated uses such as leaks, open blowing and production applications without regulators or with wide open regulators; this added demand, which the fact sheet calls artificial demand, substantially increases energy consumption.

The ULTRASCREW datasheet lists most models at more than one pressure, with a different capacity at each; see [how working pressure changes screw compressor output](https://library.ultracontrolo.com/answers/how-does-working-pressure-change-screw-compressor-output/).

## Lowering pressure safely

Fact Sheet #4 advises that if one application requires a higher pressure, it may be best to replace or modify that application instead of raising the operating pressure of the whole system. It also warns that lowering average system pressure requires caution, because large changes in demand can make the pressure at points of use fall below minimum requirements; careful matching of components, controls and storage avoids this. See [why pressure drop costs energy](https://library.ultracontrolo.com/answers/why-does-pressure-drop-cost-energy/).

The ULTRASCREW datasheet states that the variable speed version can operate over a wide pressure range of 5 to 14 bar.

### Does lowering compressor pressure save energy?

The Compressed Air Challenge Fact Sheet #4 (May 2026) says significant savings can be achieved if the compressor discharge pressure can be reduced, and advises checking with the compressor manufacturer for performance specifications at different discharge pressures.

### How much does one extra bar cost?

The ULTRASEC datasheet estimates the power consumption for an increase of 1 bar on the compressor at about 7% of the installed motor power; the Compressed Air Challenge Fact Sheet #1 (May 2026) gives the rule of thumb of 1% in operating energy costs for every 2 psi.

## Sources

- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #4: Pressure Drop and Controlling System Pressure (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-4-pressure-drop-and-controlling-system-pressure_updated2026.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #1: Assessing Compressed Air Needs (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-1-assessing-compressed-air-needs_updated2026.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #3: Compressed Air System Audits (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-3-compressed-air-system-audits_updated2026.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #6: Compressed Air System Controls (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-6-compressed-air-system-controls_updated2026.pdf)
- [ULTRASEC datasheet, p. 2](https://www.ultracontrolo.com/products/ultrasec)
- [ULTRASCREW datasheet, p. 2 and p. 3](https://www.ultracontrolo.com/products/ultrascrew)
- [ULTRASEC datasheet, p. 2](https://www.ultracontrolo.com/products/ultrasec)

Reviewed: 2026-11-19. Ultra Controlo engineering. https://library.ultracontrolo.com/answers/what-pressure-should-an-industrial-compressor-run-at/
