# What speed range suits a variable speed screw compressor?

**What speed range suits a variable speed screw compressor, and what happens below minimum speed?**

The US Department of Energy compressed air sourcebook (third edition, 2016) says a variable speed compressor has its best efficiency between 30 and 80 percent speed for the majority of its operating hours, and that continuous operation at full or minimum speed should be avoided.

The US Department of Energy sourcebook on compressed air (third edition, 2016) describes variable speed as an efficient means of rotary compressor capacity control. Compressors with variable speed drive controls continuously adjust the drive motor speed within a variable range to match demand. The sourcebook then gives limits at both ends of the speed range.

## Why the extremes cost efficiency

- At or near full output, a variable speed drive compressor uses more input power than a comparable fixed speed unit, because of the inherent drive losses.
- At low speeds the package efficiency of variable speed compressors falls off.
- The sourcebook therefore says continuous operation at full or minimum speeds should be avoided, and that best efficiency occurs if the compressor operates between 30 and 80 percent speed for the majority of its operating hours.

## Below minimum speed

Variable speed compressors typically load/unload or start/stop at output capacities below minimum speed. For lubricated screw compressors, the sourcebook says long term operation below minimum speed should be avoided, to prevent condensate contamination of the compressor lubricant. Some variable speed compressors also use variable displacement controls to enhance the machine turn-down range.

## Storage and several compressors

The sourcebook says variable speed compressors require proper effective storage to avoid continuously ramping the speed up and down, which may damage the driver. See [how an industrial air receiver is sized](https://library.ultracontrolo.com/answers/how-is-an-industrial-air-receiver-sized/).

In a plant with several compressors, the sourcebook says the trim compressor, the one that runs at part load while the others stay fully loaded, is typically the unit with the best part load efficiency, such as a variable speed compressor. See [trim compressor](https://library.ultracontrolo.com/glossary/trim-compressor/) and [how several compressors are controlled together](https://library.ultracontrolo.com/answers/how-are-several-air-compressors-controlled-together/).

## Drives in general

Fact Sheet #6 of the Compressed Air Challenge (May 2026, Rev. 1) says that variable frequency drives were historically rare on industrial air compressors because their initial cost could not justify the efficiency gain over other control schemes, that cost is no longer a major issue, and that VFDs are widely accepted in compressor applications as they become more reliable and efficient at full load.

## ULTRASCREW

The ULTRASCREW datasheet says the variable speed version can operate over a wide pressure range, 5 to 14 bar. The 30 to 80 percent band above is the sourcebook's general guidance, not a figure from any ULTRASCREW datasheet, so the speed range of a given unit comes from its manufacturer's data. See [fixed speed or variable speed](https://library.ultracontrolo.com/compare/vsd-vs-fixed-speed-compressors/) and [the ULTRASCREW versions](https://library.ultracontrolo.com/answers/ultrascrew-fsd-vs-vsd-vs-ds-vsd/).

### What happens below the minimum speed?

The sourcebook says variable speed compressors typically load/unload or start/stop below minimum speed, and that long term operation of lubricated screw compressors below it should be avoided to prevent condensate contamination of the lubricant.

### Why does a variable speed compressor need storage?

The sourcebook says proper effective storage avoids continuously ramping the speed up and down, which may damage the driver.

## Sources

- [US Department of Energy and Compressed Air Challenge, Improving Compressed Air System Performance: A Sourcebook for Industry, third edition (2016)](https://www.energy.gov/sites/prod/files/2016/03/f30/Improving%20Compressed%20Air%20Sourcebook%20version%203.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #6: Compressed Air System Controls (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-6-compressed-air-system-controls_updated2026.pdf)
- [ULTRASCREW datasheet, p. 2](https://www.ultracontrolo.com/products/ultrascrew)

Reviewed: 2026-11-19. Ultra Controlo engineering. https://library.ultracontrolo.com/answers/what-speed-range-suits-a-variable-speed-screw-compressor/
