# Why does a compressor keep loading and unloading?

**Why does a compressor keep switching between load and unload, and how do you fix it?**

According to the Compressed Air Challenge Fact Sheet #6 (May 2026), load/unload control responds to reductions in air demand by unloading the compressor, with the motor still running, so that it delivers no air for a period; Fact Sheet #7 adds that leaks force the equipment to cycle more frequently.

## How load/unload control works

Fact Sheet #6 explains that system pressure is monitored: the control decreases compressor output when pressure reaches a predetermined level and increases it again when pressure drops to a lower predetermined level. The difference between the two is the control range, which can be anywhere from 2 to 20 psi depending on air system demand. Load/unload control, also known as constant speed control, lets the motor run continuously but unloads the compressor when the discharge pressure is adequate.

In most cases, the fact sheet says, an unloaded rotary screw compressor will consume 15 to 35% of full-load horsepower while delivering no useful work, and as a result some load/unload control schemes can be inefficient.

## Common causes of frequent cycling

- Leaks: Fact Sheet #7 (May 2026) says that, by forcing the equipment to cycle more frequently, leaks shorten the life of almost all system equipment, including the compressor package. With all air-operated equipment turned off, leaks alone make a compressor load and unload as the pressure drops.
- Limited storage: the 2016 US DOE sourcebook said that for lubricated screw compressors the effective size of the system storage affected part-load efficiency, and that compressors with limited effective storage could experience short cycling, with an even greater negative effect on efficiency and reliability.
- Uncoordinated controls: the US DOE Compressed Air Tip Sheet #7 (August 2004) said that in many systems compressor controls are not coordinated with demand, which can result in compressors operating in conflict with each other, short-cycling or blowing off, all signs of inefficient system operation.
- Start/stop on a cycling load: Fact Sheet #6 says start/stop control should not be used in an application with frequent cycling, because repeated starts cause the motor to overheat and other compressor components to require more frequent maintenance.

## What the sources recommend

- Find and fix leaks: Fact Sheet #7 says the percentage lost to leakage should be less than 10% in a well-maintained system; see [compressed air leaks](https://library.ultracontrolo.com/industry/compressed-air-leaks/).
- Use storage: Fact Sheet #11 (May 2026) says air receivers provide a supply buffer for short-term demand spikes, dampen compressor pulsations and make the system easier to control, and that receivers close to points of intermittent use reduce pressure swings.
- Match control to demand: Fact Sheet #6 says all units which are on should run at full-load except one unit for trimming, and that variable frequency drives are widely accepted in compressor applications.
- Measure first: Tip Sheet #7 advised developing a pressure and a demand profile before investing in additional controls; see [how to measure a factory's compressed air demand](https://library.ultracontrolo.com/answers/how-to-measure-a-factorys-compressed-air-demand/).

ULTRASCREW compressors, supplied by Ultra Controlo, include a variable speed version; see [ULTRASCREW FSD, VSD and DS VSD compared](https://library.ultracontrolo.com/answers/ultrascrew-fsd-vs-vsd-vs-ds-vsd/) and [how several compressors are controlled together](https://library.ultracontrolo.com/answers/how-are-several-air-compressors-controlled-together/).

### Can load and unload times show how much air leaks?

For compressors with start/stop controls, the Compressed Air Challenge Fact Sheet #7 (May 2026) describes starting the compressor with all air-operated end-use equipment turned off and timing its load and unload periods, which gives the leakage as a percentage of compressor capacity.

### Does an unloaded screw compressor still use power?

Yes. The Compressed Air Challenge Fact Sheet #6 (May 2026) says that in most cases an unloaded rotary screw compressor will consume 15 to 35% of full-load horsepower while delivering no useful work.

## Sources

- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #6: Compressed Air System Controls (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-6-compressed-air-system-controls_updated2026.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #7: Compressed Air System Leaks (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-7-compressed-air-system-leaks_updated2026.pdf)
- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #11: Proven Opportunities at the Component Level (May 2026, Rev. 01)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-11-proven-opportunities-at-the-component-level_updated2026.pdf)
- [US Department of Energy, Compressed Air Tip Sheet #7: Compressed Air System Control Strategies (August 2004)](https://www.compressedairchallenge.org/data/sites/1/media/library/tipsheets/tipsheet07.pdf)
- [US Department of Energy and Compressed Air Challenge, Improving Compressed Air System Performance: A Sourcebook for Industry, third edition (2016, DOE/EE-1340), Fact Sheet 5, p. 35](https://www.energy.gov/sites/prod/files/2016/03/f30/Improving%20Compressed%20Air%20Sourcebook%20version%203.pdf)
- [ULTRASCREW datasheet, p. 2](https://www.ultracontrolo.com/products/ultrascrew)

Reviewed: 2026-11-19. Ultra Controlo engineering. https://library.ultracontrolo.com/answers/why-does-a-compressor-keep-loading-and-unloading/
