# Oil-injected or oil-free screw compressor for industry

According to Compressed Air Challenge Fact Sheet #1 (May 2026), lubricant-free air can be produced with lubricant-free compressors or with lubricant-injected compressors plus extra separation and filtration, and the choice depends on the end use, including the risk and cost of product contamination.

Both screw compressor types appear in industry, and Fact Sheet #1 says the choice starts from the end use. Quality is determined by the dryness and contaminant level the end uses require, and one of the main factors is whether or not lubricant-free air is required. Process air for food and pharmaceutical production and for electronics is one of the four air quality levels the fact sheet lists.

## Side by side

|  | Lubricant-injected screw | Lubricant-free screw |
|---|---|---|
| How it compresses (DOE sourcebook, 2016) | Lubricant is injected into the compression chamber, where it lubricates the rotors and bearings, removes the heat of compression and seals the clearances. It is then separated from the air, leaving a carry-over usually in the range of 2 to 5 ppm. | Dry type: the rotors do not touch, and lubricated timing gears outside the compression chamber keep their positions. Water-injected type: water seals the internal clearances and removes the heat of compression. |
| Stages and pressure (DOE sourcebook, 2016) | Single-stage packages have discharge pressures from 50 to 250 psig. Two-stage versions can reduce specific power, and some reach up to 500 psig. | Dry type: most designs use two stages with an intercooler. Single-stage units operate up to 50 psig, and two-stage units generally up to 150 psig. |
| Cost and efficiency (Fact Sheet #1, 2026) | Usually lower first cost, higher efficiency and lower maintenance cost than lubricant-free machines. | Usually higher first cost, lower efficiency and higher maintenance cost than lubricant-injected machines. |
| Lubricant-free air (Fact Sheet #1, 2026) | Possible with additional separation and filtration equipment, which causes some reduction in efficiency, especially if the system is not properly maintained. | Produced directly by the compressor. |

The first two rows describe the DOE sourcebook (third edition, 2016). The last two rows are Fact Sheet #1 of the Compressed Air Challenge (May 2026, Rev. 1), which says lubricant-free air can be produced with either type, and that careful consideration should be given to the specific end use for the lubricant-free air, including the risk and cost associated with product contamination, before selecting one.

## Stating the air quality

ISO 8573-1 defines purity classes for compressed air with respect to particles, water and oil. See [ISO 8573-1](https://library.ultracontrolo.com/standards/iso-8573-1/), and the air quality that food and beverage and pharmaceutical manufacturing plants ask for.

## Ultra Controlo compressors

ULTRASCREW is an oil lubricated rotary screw compressor, in fixed speed and variable speed versions; for oil-free compression, the product page refers to ULTRACECO. See [ULTRACECO oil-less compressors](https://library.ultracontrolo.com/products/ultraceco-oil-less-air-compressors/) and [the ULTRASCREW range](https://library.ultracontrolo.com/products/ultrascrew/). According to its Industrial 2026 catalogue, Ultra Controlo also distributes and services Gardner Denver compressors, including oil-free screw compressors: see [Gardner Denver compressors in Portugal](https://library.ultracontrolo.com/industry/gardner-denver-compressors-portugal/).

### Does an oil-injected compressor always deliver oil-free air?

No. Fact Sheet #1 says lubricant-free air can also be produced with lubricant-injected compressors that have additional separation and filtration equipment, which causes some reduction in efficiency, especially if systems are not properly maintained.

### Is ULTRASCREW oil-free?

No. The ULTRASCREW product page says it is an oil lubricated rotary screw compressor, and refers to ULTRACECO for oil-free compression.

## Sources

- [Compressed Air Challenge, Compressed Air Systems Fact Sheet #1: Assessing Compressed Air Needs (May 2026, Rev. 1)](https://www.compressedairchallenge.org/data/sites/1/media/library/factsheets2026/fact-sheet-1-assessing-compressed-air-needs_updated2026.pdf)
- [US Department of Energy and Compressed Air Challenge, Improving Compressed Air System Performance: A Sourcebook for Industry, third edition (2016), chapter 2](https://www.energy.gov/sites/prod/files/2016/03/f30/Improving%20Compressed%20Air%20Sourcebook%20version%203.pdf)
- [ULTRASCREW product page, ultracontrolo.com (checked 18 November 2026)](https://www.ultracontrolo.com/products/ultrascrew)
- Ultra Controlo, Industrial 2026 catalogue, pp. 10, 12 and 22
- [ISO 8573-1:2010 Compressed air, Part 1: Contaminants and purity classes (ISO catalogue page)](https://www.iso.org/standard/46418.html)

Reviewed: 2026-11-18. Ultra Controlo engineering. https://library.ultracontrolo.com/compare/oil-injected-vs-oil-free-screw-compressors-for-industry/
