Medical air
How does an oil-injected rotary screw compressor work?
Short answer
The 2016 US DOE sourcebook described the lubricant-injected (oil-injected) rotary screw compressor as two intermeshing helical rotors in a housing: air trapped between the lobes is compressed as the meshing point moves along the rotors, until the space opens to the discharge port.
Compression between two rotors
In the third edition of Improving Compressed Air System Performance: A Sourcebook for Industry (US DOE and Compressed Air Challenge, 2016), the compressor consisted of two intermeshing rotors in a machined housing, with an inlet port at one end and a discharge port at the other. The male rotor had lobes formed helically along its length and the female rotor matching helical grooves. Air entering through the inlet filled the spaces between the lobes and was trapped against the housing as rotation carried those spaces past the inlet port. As a lobe of one rotor rolled into a groove of the other, the point of intermeshing moved along the rotors, reducing the space occupied by the air and raising its pressure; compression continued until the spaces were exposed to the discharge port.
What the oil does
The Compressed Air Challenge Fact Sheet #5 (May 2026) says that in lubricant-injected rotary compressors the lubricant lubricates bearings, gears and intermeshing rotor surfaces, acts as a seal and removes most of the heat of compression, and that only a lubricant meeting the manufacturer's specifications should be used. The 2016 sourcebook used the generic term lubricant instead of oil.
Separating oil from the air
The 2016 sourcebook described the mixture of compressed air and lubricant leaving the air end for a sump/separator, where directional and velocity changes separated most of the liquid; the remaining aerosols were removed by an air/lubricant separator or a coalescing filter, leaving only a few parts per million of lubricant carry-over. A minimum pressure device prevented excessive velocities through the separator element at start-up, and in most packages the sump pressure circulated the lubricant through a filter and cooler before reinjection, with a thermostatic bypass valve keeping the lubricant at the desired temperature. An aftercooler then cooled the discharged air, and a moisture separator with an automatic drain trap removed the condensate.
Fact Sheet #10 (May 2026) explains that in air-cooled packaged rotary screw compressors ambient air passes across the aftercooler and the lubricant cooler, taking heat from both the compressed air and the lubricant, and that as much as 80 to 93% of the electrical energy consumed by an industrial air compressor is converted into heat.
Where it fits
Fact Sheet #11 (May 2026) says lubricant-injected rotary screw compressors are used in most industrial plant air applications and provide continuous flow without the pressure pulsations typical of reciprocating compressors, but that rotary screw compressors are in general less efficient at part-load than reciprocating compressors. It also states that two-stage rotary-screw compressors are more efficient than single-stage units; see when a two-stage screw compressor is worth it.
The ULTRASCREW datasheet describes ULTRASCREW as an oil injected rotary screw compressor, supplied by Ultra Controlo.
More questions
Does an oil-injected screw compressor deliver lubricant-free air?
Not on its own: the 2016 DOE sourcebook described separation leaving a few parts per million of lubricant carry-over, and the Compressed Air Challenge Fact Sheet #1 (May 2026) says lubricant-free air can be produced with lubricant-injected compressors that have additional separation and filtration equipment.
Why does the air/lubricant separator matter for energy?
The Compressed Air Challenge Fact Sheet #11 (May 2026) says the separator generally starts with a 2 to 3 psid pressure drop at full-load when new, and that an earlier replacement may make sense when electricity prices are high.
Sources
- US Department of Energy and Compressed Air Challenge, Improving Compressed Air System Performance: A Sourcebook for Industry, third edition (2016, DOE/EE-1340), Section 1, p. 7
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #1: Assessing Compressed Air Needs (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #5: Maintenance of Compressed Air Systems for Peak Performance (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #10: Heat Recovery with Compressed Air Systems (May 2026, Rev. 01)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #11: Proven Opportunities at the Component Level (May 2026, Rev. 01)
- ULTRASCREW datasheet, p. 2
Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.