Medical gas library

Industry

Screw, reciprocating or centrifugal air compressor?

Short answer

Compressed Air Challenge Fact Sheet #11 (May 2026) says lubricant-injected rotary screw compressors are used in most industrial plant air applications, single-acting reciprocating compressors are less efficient than other types, and centrifugal compressors are usually limited to high-volume applications with relatively constant demand.

Fact Sheet #11 of the Compressed Air Challenge (May 2026, Rev. 01) covers the three most common compressor types in industrial plants: reciprocating, rotary positive-displacement (screw) and centrifugal. It says lubricant-injected rotary screw compressors are used in most industrial plant air applications and for large applications in the service industries. The table sets out what it and the US Department of Energy sourcebook (third edition, 2016) say about each type.

ReciprocatingRotary screw (lubricant-injected)Centrifugal
Where it is usedIn the past, the most widely used compressors in industrial plant air systems. Single-acting units are generally air-cooled and in the smaller hp sizes.Most industrial plant air applications and large applications in the service industries.Usually limited to high-volume applications such as chemical manufacturing, textile plants, petroleum refining, or general plant air in large facilities. Best suited to relatively constant demand, or to base-load operation with other types used as trim machines.
Size (DOE sourcebook, 2016, and Fact Sheet #11)From less than 1 hp to more than 600 hp.Rotary compressors are most commonly used in sizes from about 10 to 500 hp.Available for 100 psig discharge from 100 hp, but most are 300 hp or larger.
Efficiency (Fact Sheet #11)Single-acting units are less efficient than other types. Multi-stage double-acting units are usually considered the most efficient, with high initial and installation costs and higher maintenance requirements.Typically less efficient than two-stage double-acting reciprocating or three-stage centrifugal compressors. Two-stage units are more efficient than single-stage units. Generally less efficient at part load than reciprocating compressors.Three-stage units are generally more efficient than rotary screw compressors and can approach the efficiency of double-acting reciprocating compressors.
Installation and running (Fact Sheet #11)Double-acting units are generally water-cooled and require substantial foundations.Lower initial installation and maintenance costs, smaller size, reduced vibration and noise and less floor space than reciprocating compressors. Continuous flow without pressure pulsations.Operate at high speeds, so equipment is smaller and more compact.

Efficiency, size and noise in the sourcebook

The DOE sourcebook says multi-stage, double-acting compressors are the most efficient compressors available, and are typically larger, noisier and more costly than comparable rotary units.

Lubricant-free machines

Fact Sheet #11 says lubricant-free versions of reciprocating and rotary compressors are available, and that centrifugal compressors are inherently lubricant-free. Lubricant-free rotary screw and reciprocating compressors are generally less efficient than lubricant-injected machines. See oil-injected or oil-free screw compressors for industry.

Choosing

The fact sheets compare types in general. Efficiency between models of one type is compared on the same test basis: see how air compressor efficiency is compared, and how an industrial air compressor is sized for the demand side. For a medical air plant the question is different: see scroll, screw or piston medical air compressors.

ULTRASCREW

The ULTRASCREW datasheet describes an oil injected rotary screw compressor. See the ULTRASCREW range and rotary screw compressor.

More questions

Which type is the most efficient?

Fact Sheet #11 says multi-stage double-acting reciprocating compressors are usually considered the most efficient, and that three-stage centrifugal compressors are generally more efficient than rotary screw compressors and can approach their efficiency.

Why are screw compressors so common in plants?

Fact Sheet #11 lists lower initial installation and maintenance costs, smaller size, reduced vibration and noise, reduced floor space and continuous flow without pressure pulsations compared with reciprocating compressors.

Sources

Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.

Reviewed: · Ultra Controlo engineering · Markdown version

Related