Medical air
How do hot or freezing sites affect a compressed air dryer?
How do high inlet and ambient temperatures, or freezing conditions, affect a compressed air dryer?
Short answer
According to the 2016 US DOE sourcebook, a higher dryer inlet temperature reduces its rated capacity, and refrigerant-type dryers are not recommended where ambient temperatures are below freezing, because moisture in the compressed air can freeze and damage the dryer.
Hot inlet air
The 2016 US DOE sourcebook says dryer ratings usually are based on standard inlet conditions of 100 psig, 100 °F inlet compressed air temperature and 100 °F ambient temperature, and that an increase in inlet temperature or a decrease in inlet pressure reduces the dryer's rated capacity. Most manufacturers provide correction factors for this, and dryers must be sized for the worst case operating inlet temperature, system pressure and ambient temperature.
In its maintenance fact sheet the sourcebook adds that because dryers are normally designed at 100 °F maximum inlet air temperature, some remedial action may be required if aftercooler outlet temperatures exceed 100 °F. Compressed Air Challenge Fact Sheet #11 (May 2026) says air treatment equipment should be operated as close to the manufacturer's design conditions as possible.
Freezing conditions
The sourcebook says refrigerant-type air dryers, cycling and non-cycling, are not recommended for operation in sub-freezing ambient temperatures, because the moisture in the compressed air can freeze and damage the dryer. It also says that to avoid freezing, the evaporator temperature should not go below 32 °F.
In a hospital medical air plant
HTM 02-01 (2026), the NHS England guidance, says that manufacturers should be consulted over the range of operating temperatures for which the supply system is designed, and that in extreme cases refrigerator cooling may be required between the compressors and the dryer and filter set. In its dental air chapter the HTM says most dental plant is rated for an operational ambient temperature range of 10 to 35 °C with an optimum range of 10 to 15 °C, and that the performance of the compressor and dryer may be seriously impaired if the ambient temperature rises above 35 °C.
Inlet temperature limits in two Ultra Controlo datasheets
| Dryer | What the datasheet gives |
|---|---|
| ULTRASEC (refrigeration) | Maximum compressed air inlet temperature of 70 °C for ULTRASEC standard and 100 °C for ULTRASEC-HT |
| ULTRADRY (adsorption) | Inlet temperature minimum +5 °C, maximum +50 °C; table values are at +35 °C inlet and 7 bar g operating pressure |
These are compressed air inlet temperatures, not ambient temperatures.
More questions
Can a refrigerated dryer work in freezing conditions?
The 2016 US DOE sourcebook says refrigerant-type air dryers are not recommended for operation in sub-freezing ambient temperatures, because the moisture in the compressed air can freeze and damage the dryer.
What compressed air inlet temperature do the ULTRASEC and ULTRADRY datasheets give?
The ULTRASEC datasheet gives a maximum of 70 °C (100 °C for ULTRASEC-HT). The ULTRADRY datasheet gives a minimum of +5 °C and a maximum of +50 °C.
Sources
- US DOE and Compressed Air Challenge, Improving Compressed Air System Performance, 3rd edition (2016): Introduction, p. 12 (PDF p. 17); Fact Sheet 7, p. 49 (PDF p. 54); Fact Sheet 8, p. 53 (PDF p. 58)
- Compressed Air Challenge, Fact Sheet #11, Proven Opportunities at the Component Level (May 2026), p. 3
- NHS England, HTM 02-01 Part A (August 2026 edition): 7.17 and 9.21
- ULTRASEC datasheet, pp. 2 to 3
- ULTRADRY datasheet, p. 3
Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.
Related
- AnswersHow is a compressed air dryer sized?
- AnswersWhat causes a high dew point alarm on a medical air dryer?
- AnswersRefrigeration or adsorption dryer for medical air?
- AnswersHow does ambient temperature affect a PSA plant?
- IndustryDryers and filters for industrial compressed air
- ProductsULTRASEC: specifications and models