Medical air
How to choose an industrial air compressor
How do you choose an industrial air compressor for a factory?
Short answer
The Compressed Air Challenge fact sheets (May 2026) say the choice starts from the end uses: the air quality, quantity and pressure they need and how demand varies over time. They then compare compressor type, controls and tested efficiency on part-load performance and life-cycle cost, not on purchase price alone.
Start from what the end uses need
Compressed Air Systems Fact Sheet #1 (Compressed Air Challenge, May 2026, Rev. 1) defines compressed air needs by the air quality, quantity and level of pressure required by the end uses in the plant. Quality ranges from plant air through instrument air and process air to breathing air, and industrial applications typically use one of the first three levels. The higher the quality, the more the air costs to produce.
One of the main factors in air quality is whether lubricant-free air is required. The fact sheet notes that it can be produced either with lubricant-free compressors or with lubricant-injected compressors that have additional separation and filtration equipment (oil-free or oil-injected).
Pressure comes from the ratings of the tools and the process, and required pressure levels must take into account the losses in dryers, separators, filters and piping. As a rule of thumb, the fact sheet says every 2 psi increase in operating pressure requires an additional 1% in operating energy costs.
Read the load profile
Fact Sheet #1 treats the variation of demand over time as a major consideration in system design. Plants with wide variations in demand need a system that operates efficiently at part load, while plants with a flatter load profile can use simpler control strategies. It calls oversized compressors extremely inefficient, because most systems use more energy per unit volume of air when running at part load, and says that in many cases multiple smaller compressors with sequencing controls make sense. Fact Sheet #6 (May 2026) adds that the type of controls is largely determined by the compressor type and the facility's demand profile. The sizing steps are in how to size an industrial air compressor, and the variable speed question in when a variable speed compressor makes sense.
Compare types and tested efficiency
According to Fact Sheet #11 (May 2026), lubricant-injected rotary screw compressors are used in most industrial plant air applications. They provide continuous flow without the pressure pulsations typical of reciprocating compressors, but are in general less efficient at part load than reciprocating compressors (screw or piston).
To compare offers, Fact Sheet #8 (May 2026) names ISO 1217 as the recognized performance standard for displacement compressors, including rotary screw machines. It says buyers should make sure compressors were tested to the same standard and at the same conditions, and should compare part-load efficiency as well (what a compressor tender should specify).
Decide on life-cycle cost
Fact Sheet #9 (May 2026) calls electricity by far the largest expense of owning and operating a compressed air system and recommends life-cycle cost analysis, warning that too often users are only concerned with initial cost and accept the lowest bid, ignoring system efficiency.
Ultra Controlo supplies ULTRASCREW oil injected rotary screw compressors. It also distributes and services Gardner Denver in Portugal, whose EnviroAire T/TVS oil-free screw compressors the manufacturer describes as certified Class 0 for no oil content by TÜV.
More questions
Is one large compressor or several smaller ones better?
Fact Sheet #1 (May 2026) says that in many cases it makes sense to use multiple, smaller compressors with sequencing controls, so that operation stays efficient when demand is below peak.
Which air quality do factories usually need?
According to Fact Sheet #1 (May 2026), industrial applications typically use plant air, instrument air or process air, the first three of its four quality levels; breathing air is the fourth.
Sources
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #1: Assessing Compressed Air Needs (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #6: Compressed Air System Controls (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #8: Packaged Compressor Efficiency Ratings (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #9: Compressed Air System Economics (May 2026, Rev. 1)
- Compressed Air Challenge, Compressed Air Systems Fact Sheet #11: Proven Opportunities at the Component Level (May 2026, Rev. 01)
- ULTRASCREW datasheet, p. 2
- Ultra Controlo, Industrial 2026 catalogue, p. 10 (partner brands)
- Gardner Denver, EnviroAire T/TVS 90-160 kW (EMEIA)
Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.
Related
- AnswersHow is an industrial air compressor sized?
- ComparisonsVariable speed vs fixed speed compressors
- ComparisonsOil-injected or oil-free screw compressor for industry
- ComparisonsScrew, reciprocating or centrifugal air compressor?
- AnswersHow is air compressor efficiency compared?
- ProductsULTRASCREW: specifications and models