Medical gas library

Medical air

How do you measure a factory's real compressed air demand?

How do you measure how much compressed air a factory really uses?

Short answer

According to the Compressed Air Challenge Fact Sheet #3 (May 2026), demand is established as a load profile: flow and pressure are measured across the system under different demand conditions while observing the load on the existing compressors, over a 24-hour period or several days if demand varies significantly.

Average demand, not the sum of maximums

Fact Sheet #1 (May 2026) says required capacity can be found by summing the requirements of the tools and process operations, taking into account load factors, and that the total air requirement is not the sum of the maximum requirements of each tool and process but the sum of their average air consumption. High short-term demands should be met by air stored in an air receiver.

What to measure, and with what

Fact Sheet 10 of the 2016 US DOE sourcebook, on baselining, said a system's baseline required measurement of power, pressure, flow and temperature under different operating conditions, plus an estimate of the leak load, always correlated to production levels. It listed the tools: matched, calibrated pressure gauges or differential pressure gauges; a hook-on amp/volt meter, or preferably a kW meter; data loggers, used to create plant pressure, flow and energy consumption profiles; and a flow meter, chosen by type (in-line or insertion), air quality (wet or dry), ease of installation, life cycle cost including any pressure drop, and accuracy.

  • Flow: the 2016 sourcebook said to measure it on the main compressor room output during all shifts and at potential inappropriate uses, and that mass flow meters compensated for pressure and temperature variations, with their standard reference conditions to be checked.
  • Power: the 2016 sourcebook said full-load and no-load input power to the compressor should be measured, that spot readings of amps and volts gave only a rough estimate, and that a wattmeter with data logging gave a direct reading of kW. Fact Sheet #9 (May 2026) also says electrical measurements of full-load amps and volts are a more accurate way to determine electricity consumption than a nameplate estimate, and that its calculations give a good estimate, not an exact number.
  • Leaks: Fact Sheet #7 (May 2026) describes estimating leakage with no demand on the system, by timing the load and unload periods of a start/stop compressor or, with other controls, the pressure decay of a known system volume.
  • Over time: Fact Sheet #5 (May 2026) advises benchmarking power, pressure and flow periodically; if power use at a given pressure and flow goes up, the system's efficiency is degrading.

Reading the profile

Fact Sheet #3 says a facility with a varying load profile will likely benefit from advanced control strategies, and one with short periods of heavy demand may benefit from storage options. It adds that a comprehensive audit should examine both supply and usage and their interaction, and that independent auditors should give recommendations which are system-neutral and commercially impartial.

The assessment standard

ISO 11011:2013, Compressed air, Energy efficiency, Assessment, sets requirements for conducting and reporting a compressed air system assessment that considers the entire system, from energy inputs to the work performed. It treats the system as three functional subsystems, supply, transmission and demand, where demand includes all compressed air consumers, productive end uses and the various forms of compressed air waste, and it also covers data analysis, reporting and the roles of those involved.

Once the load profile is known, a compressor can be matched to it: see how an industrial air compressor is sized.

More questions

Is a compressor's nameplate enough to know its energy use?

The Compressed Air Challenge Fact Sheet #9 (May 2026) gives a simple estimate from nameplate data and running hours, and says electrical measurements of full-load amps and volts are a more accurate way to determine electricity consumption.

Which standard covers compressed air system assessments?

ISO 11011:2013, Compressed air, Energy efficiency, Assessment, which sets requirements for conducting and reporting an assessment of the whole system, from energy inputs to the work performed.

Sources

Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.

Reviewed: · Ultra Controlo engineering · Markdown version

Related