Medical gas library

Vacuum and AGSS

What vacuum level does an industrial process need?

What vacuum level do common industrial processes need, from rough to fine vacuum?

Short answer

According to Elmo Rietschle, its SVT central vacuum pumps run at 100 to 250 mbar(abs), and it publishes ultimate vacuums from 150 mbar (abs.) for the dry-running V-VTN vane pump to 0.08 mbar (abs.) for the S-VSI dry screw pump; a process figure and a pump figure have to be compared in the same notation.

Makers publish pump figures, not process set points: Elmo Rietschle says in its 2026 Product Guide that its screw pumps operate at any pressure between end vacuum and atmospheric pressure. The table pairs uses that the makers list with the figure they give for the pump they list for that use.

Pump figures, not process set points; each figure is for the series named.
Use the maker listsPump the maker lists for itFigure the maker publishes for that pump
Central vacuum systemsElmo Rietschle SVT, oil-lubricated screw with variable speedStable vacuum at 100 to 250 mbar(abs); SVT 1000 ultimate vacuum 1 mbar(a)
Small vacuum packaging machinesElmo Rietschle V-VCB, oil-lubricated rotary vaneUltimate vacuum 2 mbar (abs.)
CNC routing in woodworkingElmo Rietschle V-VTN, dry-running rotary vaneUltimate vacuum 150 mbar (abs.)
Vapour-rich or humid processes; ceramic and brick industry, drying systemsElmo Rietschle L-BV5, liquid ringSuction pressure up to 33 mbar
Pneumatic conveying; vacuum lifting; packaging supportElmo Rietschle G-Series side channel blowersPlaced by the maker in the low to medium vacuum range

Absolute or relative

Elmo Rietschle writes most of its figures as mbar (abs.) and Circutec as mbar abs. Thomas gives negative values, such as -850 mbar for the PICOLINO VTE range. Compare a process requirement and a pump figure in the same notation.

Where each technology stops

  • Liquid ring: the achievable ultimate vacuum is limited by the vapour pressure of the operating liquid and falls as the liquid warms (Elmo Rietschle); Circutec gives suction pressures down to 33 mbar abs., and down to 5 mbar abs. with gas ejectors.
  • Oil-lubricated rotary vane: the oil makes the seal that allows deeper vacuum levels, 0.5 mbar (abs.) on the V-VCS.
  • Claw: the C-VLU reaches as low as 30 mbar (abs), which the maker says was previously only attainable by oil-lubricated pumps.
  • Screw: 0.08 mbar (abs.) ultimate vacuum for the dry S-VSI.
  • Booster sets: when both high end vacuum and suction capacity are required, Elmo Rietschle combines rotary lobe boosters with oil-lubricated vane or screw backing pumps.
  • Side channel: the maker says these blowers excel at high flow rates and moderate vacuum.

The general terms of vacuum technology are defined in ISO 3529-1:2019, the second edition, last confirmed by ISO in 2024. ISO 21360-2:2020 covers positive displacement vacuum pumps with a usual base pressure below 10 kPa. For choosing between technologies, see how to choose an industrial vacuum pump.

Ultra Controlo distributes and services Elmo Rietschle vacuum pumps and blowers and Speck Pumpen (Circutec) in Portugal as partner brands, and its UltraCare programme covers preventive and corrective maintenance, original spare parts and emergency support for partner-brand equipment.

More questions

Is ultimate vacuum the pressure a process runs at?

No: it is the lowest pressure the maker publishes for the pump. Elmo Rietschle says its screw pumps operate at any pressure between end vacuum and atmospheric pressure, and sets its SVT pumps for central vacuum at 100 to 250 mbar(abs).

Why does a liquid ring pump lose vacuum when its water warms up?

Elmo Rietschle says that as the operating liquid temperature rises its vapour pressure rises and the achievable ultimate vacuum decreases; it advises cooling the liquid or using a circuit with a heat exchanger.

Sources

Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.

Reviewed: · Ultra Controlo engineering · Markdown version

Related