Vacuum and AGSS
How to choose an industrial vacuum pump
How do you choose an industrial vacuum pump: vacuum level, flow, gas and duty?
Short answer
Elmo Rietschle's FAQ says the choice depends on the desired vacuum level, the required flow rate, whether the application is wet or dry, the operating conditions and any specific requirements; ISO 21360-2:2020 sets how flow, base pressure and water vapour tolerance are measured.
1. The vacuum level, in absolute terms
Datasheets state the lowest pressure a pump reaches in different notations. Elmo Rietschle gives ultimate vacuum in mbar (abs.), for example 0.5 mbar (abs.) for the oil-lubricated V-VCS and 150 mbar (abs.) for the dry-running V-VTN; Thomas gives negative values, such as a maximum vacuum of -850 mbar for the PICOLINO VTE range. Compare pumps in the same notation. See what vacuum level a process needs.
2. The flow at that vacuum
Thomas states, in its PICOLINO VTE and DTE datasheet, that the listed flow values relate to air at the pump inlet condition, that is, expanded under vacuum. Elmo Rietschle gives nominal suction capacity at a stated supply frequency, for example 50 Hz in datasheet D236 for the V-VCS and V-VCX 200 and 300. Speck Pumpen (Circutec) gives a suction capacity tolerance of -10% for its liquid ring pumps (process industry brochure, 06/2018). For pump-down times and continuous gas loads, see how to size a vacuum pump.
3. The gas
- Moisture, steam or condensate: Elmo Rietschle calls liquid ring pumps ideal and notes that they can condense vapour within the conveyed gas; it designs its screw pumps for high vapour and liquid tolerances.
- Water vapour in an oil-lubricated vane pump: the maker offers XD versions for high water vapour loads and solvent resistance; the V-VCX has chemically resistant resin vanes and an adjustable gas ballast valve.
- Humid processes with claw pumps: the C-VLR XD version, with a protective coating for humid and wet conditions.
- Side channel blowers: the maker prefers clean, dry gases and asks for properly designed inlet conditions, with filters and particle protection.
- Aggressive media in liquid ring pumps: Elmo Rietschle calls material and coating selection critical when the medium is aggressive, abrasive or prone to scaling.
- Oxygen: the maker lists select rotary vane models for oxygen conveying and an oxygen version of its screw pumps.
- Explosive atmospheres: Elmo Rietschle lists ATEX certification for its side channel blowers; the US EPA WaterSense at Work guide (October 2012) notes that a facility removing explosive or corrosive gases might only be able to consider a liquid ring pump.
4. Oil in the process
Elmo Rietschle says oil-lubricated pumps offer high performance and can handle certain contaminants, while oil-free pumps eliminate the need for oil and suit applications where oil-free operation is critical, such as the pharmaceutical or food industries. An oil-lubricated vane pump separates oil particles from the gas in a de-oiling chamber; the maker rates the oil carryover of its SVT lubricated screw pumps at ≤3 ppm.
5. Duty, control and water
- Variable load: Elmo Rietschle says frequency converters adapt side channel blower speed and performance to changing load, especially when suction demand or differential pressure fluctuates, and the SVT controller coordinates up to 8 pumps with trim and base-load logic.
- Running hours: the G-Series side channel page gives up to 20,000 hours between services.
- Water and cooling: the US EPA guide WaterSense at Work (2012), written for commercial and institutional facilities, puts sealing and cooling water for a liquid ring pump at 0.5 to 1.0 gallons per minute per hp, and says an air-cooled dry pump can eliminate the pump's water use. See seal water for liquid ring pumps.
- Measured data: ISO 21360-2:2020, the current edition and under revision at ISO, sets methods for the volume flow rate, base pressure, water vapour tolerance, power consumption and lowest start-up temperature of positive displacement vacuum pumps with a usual base pressure below 10 kPa.
Ultra Controlo distributes and services Elmo Rietschle vacuum pumps and Thomas pumps in Portugal as partner brands, and its UltraCare programme covers preventive and corrective maintenance, original spare parts and emergency support for partner-brand equipment.
More questions
Can one pump give both vacuum and pressure?
In some technologies: Elmo Rietschle makes dry-running rotary vane pressure-vacuum units such as the V-KTR, with an operating range of -0.6 bar / +0.6 bar, and the C-KLR claw unit, with vacuum up to -0.6 bar and pressure up to +1.0 bar.
Which data should a pump offer be compared on?
ISO 21360-2:2020 covers volume flow rate, base pressure, water vapour tolerance, power consumption and lowest start-up temperature for positive displacement vacuum pumps; Elmo Rietschle adds that the nature of the application, wet or dry, and the operating conditions shape the choice.
Sources
- Elmo Rietschle, FAQ
- Elmo Rietschle, Liquid Ring Vacuum Pumps and Compressors
- Elmo Rietschle, Rotary Vane Vacuum Pumps
- Elmo Rietschle, Oil-Lubricated Rotary Vane Pumps
- Elmo Rietschle, Oil Rotary Vane Pump V-VCS
- Elmo Rietschle, Oil-Lubricated Rotary Vane Pump V-VCX
- Elmo Rietschle, Datasheet D236 V-VCS / V-VCX 200, 300 (PDF)
- Elmo Rietschle, Dry Running Rotary Vane Pumps
- Elmo Rietschle, Dry Running Rotary Vane Pump V-VTN
- Elmo Rietschle, Screw Vacuum Pumps
- Elmo Rietschle, SVT Series
- Elmo Rietschle, Dry running claw vacuum pump C-VLR 301, 401, 501
- Elmo Rietschle, Dry running claw pressure / vacuum pumps C-KLR 80-140
- Elmo Rietschle, Side Channel Blowers
- Thomas, PICOLINO VTE | DTE Series, product data sheet (PDF)
- Speck Pumpen (Circutec), Liquid and Vacuum Pumps in the Process Industry, brochure 06/2018 (PDF)
- US EPA, WaterSense at Work, Section 7.3 Vacuum Pumps (October 2012)
- ISO 21360-2:2020, Vacuum technology: standard methods for measuring vacuum-pump performance, Part 2: Positive displacement vacuum pumps
- Ultra Controlo, Industrial 2026 catalogue, pp. 10 and 22
Ultra Controlo figures come from its technical datasheets. Third-party facts were read at the source on the date shown.